Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes
  • Show More Model Years
  • Show Fewer Model Years

Pedals

Bigger, grippier, lighter and as tough as ever. The Penthouse Flat MK5 pedal is here! After two years of development and testing the MK5 Penthouse Flat is here. Retaining our signature toughness, the MK5 is the lightest and grippiest Burgtec pedal to date. We did this by not only increasing the size of the pedal platform but also how concave it is. Furthermore, we reduced the diameter of the pins and added the most wear-resistant internals on the market. From the outside to the inside, we've sweated the details of the MK5 to bring you the ultimate flat pedal. - Weight: 379g - Platform material: 7075 Alloy - Profile: 15mm - Platform: 100mm x 102mm - Dish: 2mm (concave) - Pin material: Stainless steel - Pin width: 3.5mm - Pin height: 4.5mm - Axle Material: EN24T Steel - Internals: 2 x Igus W300 bushings, single sealed bearing and inboard rubber oil seal
$6.50
The Curve Sole Measurement Tool works in conjunction with the flat sole shims to correct the radius of flat sole shoes and prevent unwanted squeaking. There are 4 radius measurements, one per side, that measure the sole and indicate whether a shim is needed or not.
$7.99
Pre-cut traction tabs designed to integrate with the Highline remote lever and increase grip for ultimate control.
$8.79
Replacement straps for Sunlite FlatForm II pedals - Strap size: 340 x 55mm
$9.00
Dimension Nylon Basic Toe Straps -Durable metal buckle -Multi-purpose strap can also be used as a lash strap for bike touring or rear rack (caution must be used to keep the strap tail out of the wheel) - 450mm
$9.99
Polyurethane pads with diamond plate traction pattern allow riders to customize their pedals for a perfect interface with any shoe. - Kit includes eight 1mm traction pads and eight 2mm traction pads
$9.99
Customize and optimize the shoe/pedal interface. - Refine the interface between the shoe tread and pedal body - Four (4) contact sleeves - 1mm thickness
$9.99
Dimension Junior Pedals. - Molded nylon, 1-piece, caged-type pedals - Built-in reflectors, will not accept toe clips - Overall pedal size is 80 x 60mm - Pedal Body Material: Plastic - Pedal Spindle: 9/16-inch or 1/2-inch - Pedal Type: Platform - Spindle Material: Chromoly Steel - Weight: 230g (9/16-inch); 304g (1/2-inch)
$9.99
Dimension Toe Straps. - Durable metal buckle - Multi-purpose strap can also be used as a lash strap for bike touring or rear rack (caution: must be used to keep the strap tail out of the wheel) - 440mm length
$9.99
RaceFace Chester Pedal Pin Kit 20 Pins Black
$9.99
IGUS Bushing replacements for your Spike or Oozy pedals help to eliminate any play that develops over time, and revive smooth spinning action. - 2pcs IGUS self lubricating bushing - 2pcs O-ring - 2pcs stainless shim washer
$9.99 - $19.99
- Plastic nylon molded body - Chromoly spindle - 318g pair
$9.99 - $15.99
- Real leather material - Classic design fits most caged pedals
$9.99
- City/road half clips - With reflectors - No straps needed - Resin
$9.99
- Heavy-duty nylon toe straps with classic style steel buckles - Narrow design fits most cage style pedals - 460mm length
$10.00
Eliminate cleat wear and improve walking comfort and safety with these Exustar cleat covers. - Compatible with Exustar cleat C01, C03, and C05 - Durable and flexible rubber - Can be used with either floating or fixed position cleats - Weight of only 14 grams/pair
$11.00
Dimension Mini Toe Clips - Toe clips do not accept toe straps - Sold as a pair - Mounting hardware for the toe-clip is included
$11.00
Dimension Toe Clips and Straps Set. Includes: - 4 bolts - 4 nuts (washers included) - 2 nylon toe straps - 2 toe clips
$11.99
Crank Brothers' 5050 Pin Kit includes 40 8mm-long steel pins that let you customize the traction on your 5050 or Mallet pedals. Thread lock is pre-applied to every pin.
$11.99 - $24.99
The super popular Impulse Pedals feature 12 traction pins per side and a knurled, concave body for superior grip. Keep your bike looking fresh and swaggy! Product Specifications - Size: 9/16" - Body: Nylon Composite - Spindle: Chromoly Steel - Installation: 15mm Pedal Wrench or 6mm Allen Key - Pins: 12 molded traction pins per side - Weight: 14.2oz
$11.99
Crank boots designed for RaceFace Next R cranksets.
$11.99
Crank boots designed for RaceFace Next SL G5 cranksets.
$11.99
- One-piece resin body - Chromoly spindle - Toe clip compatible - 366g pair
$12.00
Eliminate cleat wear and improve walking comfort and safety with these Exustar cleat covers. - Compatible with Look Keo System - Durable and flexible rubber - Can be used with either floating or fixed position cleats - Weight of only 45 grams/pair
$12.99
Protect the soles of your shoes with the Shoe Shields from Crank Brothers. These stainless-steel plates install under your cleats and prevent the pedal from digging in to your carbon-soled shoes. - Sold in pairs
$12.99
- Strapless design is easy to engage without fully committing to the pedal - No special shoes required - Improves pedaling efficiency - Molded from unbreakable nylon - Please make sure your pedals have visible mounting points or a removable reflector for mounting prior to purchase - Includes mounting hardware. Note: metal plate may not be required during installation.
$12.99
Replacement pin set for Race Face Atlas and Aeffect pedals.
$13.00
Giant's AC Toe Clips and Straps includes two durable chrome-plated steel clips, mounting hardware and a pair of quality leather straps with chrome-plated steel buckles.
$13.00
The Keo Spacer adaptors are slim wedges that fit between the shoe and the cleat. They aim to avoid the unpleasant creaking sound provoked by contact between the sole and the cleat, which can arise in particular with flat-soled shoes. Delivered with 2 spacers and 6 screws for quick and easy installation.
$13.99
Squatch platform pedals have a low-profile, nylon construction and molded traction studs that are easier on the shin in the event of a crash or pedal slip. - EPB bearing system - Spindle size: 9/16-inch
$13.99 - $24.99
Odyssey Twisted PC pedals-extremely simple, lightweight, inexpensive and famously durable plastic-bodied design.Often duplicated but never replicated. - High-strength plastic composite
$13.99
- Nylon clips - Woven straps - For ATB or hybrid use
$13.99
- One-piece ABS resin body - Molded pins - 320g pair
$13.99
- One-piece nylon body - Chromoly spindle - Toe clip compatible - 407g pair
$14.95 - $19.99
- Set of 44 total replacement steel pins for vault pedals - Run threads-out for maximum traction or flip the pins to heads-out for less grip - 16 Short pins (for use in the center) overall length 8.5mm, stud is 4.5mm - 28 Long pins (for use in the outside edge) overall length 12.5mm, stud is 4.5mm - Use either a 5mm spanner or the included 2mm hex wrench to secure/remove
$14.99 - $19.99
Everything you need to keep those Crank Bros pedals spinning freely is found in their Pedal Rebuild Kit. Each kit includes parts and instruction to rebuild one pair of Crank Bros. pedals.
$14.99
Engineered to optimize the interface between the pedal and shoe for ultimate performance and power transfer. The kit includes: - 8 × 1mm traction pads - 8 × 2mm traction pads Compatible with: - Mallet E - Model years 2016 – present
$14.99
Longer rear load pins for the outer extremities of your pedals provide ultimate durability, while shorter front load center pins create a virtual concavity in the pin pattern, increasing grip without sacrificing pedal body thinness. - 28pcs rear load pins - 16pcs front load pins - Tool included
$14.99 - $19.99
- One-piece resin bodies - Barefoot-friendly rubber surfaces - Boron-steel axles - No reflectors - 400 grams/pair
$14.99 - $19.99
- One-piece ABS resin body - Non-slip rubber surface - Boron spindle - 388g pair
$14.99
- One-piece resin body - Juvenile size platform - Boron spindle - 390g pair
$15.99
- Cleat covers to avoid wear and provide stability and grip while walking - Lightweight, flexible and durable
$15.99
- One-piece resin body - Barefoot friendly rubber surface - Includes reflectors
$15.99
- One-piece resin body with rubber surface for grip - Boron spindle - 400g pair
$16.00
Dimension City Pedals. - Built-in reflectors, will not accept toe clips - Molded nylon; 1-piece, caged-type pedal - Slip-resistant surface
$16.00
Dimension Mountain Basic Pedals. - Molded nylon 1-piece, caged-type pedal with reflectors - Accepts toe clips - Hang tag packaging - Pedal Body Material: Plastic - Pedal Spindle: 9/16-inch or 1/2-inch - Pedal Type: Toe Clip Compatible - Spindle Material: Chromoly Steel - Weight: 330g
$16.00
The Cleat Shim-Spacer helps compensate for leg length discrepancies.
$16.99
- Chrome plated steel clips for double toe strap - Hardware included - Deep size for shoes with a larger toe-box
$17.00
- Extend the life of your iSSi Thump pedals by replacing beat-up or missing pins with the Thump Replaceable Pin Kit. - Includes 36 steel pins and 2mm spacers to replace both sides of two pedals - The standard pin height out of the box is 3mm with a 2mm spacer. For more traction, remove the spacer under the pin head to increase pin height to 5mm.
$17.10
Wheels Manufacturing Pedal Washers help distribute the forces of a pedal spindle on your expensive crank arms and allow you to torque pedals properly over and over again without damaging crank arms.
$17.99
- Chrome plated steel body and cage - Built in reflectors
$17.99
- Nylon co-molded body with rubber tread surface - Reflectors included - 9/16"
$17.99
Xpedo cleat set for Xpedo M-Force pedals - Weight: 65g per set with hardware
$18.00
- Shimano SPD-SL-style - Engineered thermoplastic injection body - Anti-slip walk pads - Fixed position with no float
$18.99
PIN KIT FOR OUR COMPOSITE PEDALS KIT CONTAINS: - 40 THREADED M3x10mm SOCKET HEAD PINS - 40 NYLOCK NUTS
$19.00
- Compatible with LOOK cleats system. - 3 float options (0/4.5/9). - Memory position for separate front and rear cleat.
$19.99
The Jonesin' pedal is the little brother of the Safari pedal, designed using the same basic principles of extra hexagonal studs and a true dual concave DX style platform but with a slimmer body for a closer to the axle feel. - Tough nylon fiberglass construction - True dual concave design - Knurled surface for extra grip - 18 optimally placed hexagonal pins per side
$19.99
Dimension Cruiser/Comfort Pedals. - Forged aluminum platform-type body with slip-resistant surface and built-in reflectors - Platform size is 105.5 x 74mm - Pedal Body Material: Aluminum - Pedal Spindle: 9/16-inch - Pedal Type: Platform - Spindle Material: Chromoly Steel - Weight: 448g
$19.99
Dimension Mountain Sport Pedals. - Molded nylon pedal body - Accepts toe clips - Pedal Body Material: Plastic - Pedal Spindle: 9/16-inch - Pedal Type: Toe Clip Compatible - Spindle Material: Chromoly - Weight: 290g
$19.99
The KEO cleat covers are designed to protect your KEO cleats while walking. Compatible with KEO GRIP and KEO CLEAT, these covers lengthen the life of your cleats and improve safety when walking thanks to an anti-slip surface. - Compatibility: KEO Grip/KEO Cleat - Use: Protect the cleat
Page 1 of 7 Next page